Dynasty Spas Hot Tub SC MP DY5 User Manual

SC-MP-DY5 / Dual-Pump System  
The Quick Reference Card provides a quick overview of your spa's main  
functions and the operations accessible with your digital control pad.  
Starting Pump 1 & Pump 2:  
Turning the light on:  
Press Pumps once to turn pump 1 on at low  
speed. Pressing a second time turns Pump 1 and  
Pump 2 to high speed. A third time turns both  
pumps off. A built-in timer automatically turns  
pumps off after 20 minutes (Pump 1 low speed  
after 2 hours), unless manually deactivated first.  
Press Light to turn light on. Pressing a second time  
turns light off. A built-in timer automatically turns  
light off after 2 hours, unless manually deactivated  
first.  
The "Light" indicator is displayed  
when light is on.  
The "Pump 1" indicator flashes  
when Pump 1 is on at low speed.  
Fiber Box Option: If spa has an optional fiber box,  
press Light key to turn fiber box (motor and light)  
on. Pressing a second time turns fiber box off but  
leaves light on. A third time turns both motor and  
light off. A built-in timer turns fiber box off after  
2 hours, unless it has been manually deactivated.  
The "Light" indicator is displayed when fiber box  
light is on. It flashes when fiber box motor and light  
are on at the same time.  
"Pump 1" and "Pump 2" indicators  
light up when both pumps are on  
at high speed.  
Starting the blower:  
Press Blower once to turn blower on. Pressing a  
second time turns blower off. A built-in timer auto-  
matically turns blower off after 20 minutes, unless  
manually deactivated first.  
LED Light Option: If spa has an optional LED  
light, press Light key to turn LED lights on. To  
advance to the next color/display setting, press  
Light key twice. The LEDs will go off with the first  
press, then back on in the next setting with the  
second press. If the LEDs remain off for more  
than 5 sec., the color/ display sequence will reset  
and start back at the beginning the next time the  
Light key is pressed. Color/ display sequences are:  
The "Blower" indicator lights up  
when blower is on.  
Setting water temperature:  
Use Up or Down arrow keys to regulate water  
temperature. The temperature setting will be  
displayed for 5 seconds to confirm your new  
selection.  
1• LEDs light up and slowly cycle through all six  
colors. The slow cycle restarts at the begin-  
ning and repeats.  
2• LEDs light up and remain on in Aqua.  
3• LEDs light up and remain on in Purple.  
4• LEDs light up and remain on in Blue.  
5• LEDs light up and remain on in Gold.  
6• LEDs light up and remain on in Green.  
7• LEDs light up and remain on in Red.  
8• LEDs light up for 2 sec., flash off, then flash  
on in the next color until all six colors have  
been displayed. The flashing cycle then  
repeats itself.  
The "Set Point" indicator displays the  
desired temperature, NOT the current  
water temperature!  
Water temperature can be adjusted by 1˚ in-  
crements from 59 to 104˚F (15 to 40˚C).  
Temperature display unit:  
Press and hold Light key for 5 seconds to display  
water temperature in either Fahrenheit (˚F) or  
Celsius (˚C). If a power-up occurs, system re-  
turns to default setting (˚F).  
9• LEDs flash on/off quickly for a strobe light  
effect. A built-in timer turns lights off after  
2 hours unless manually deactivated first.  
The "Light" icon is displayed  
when LED light is on.  
 
Quick Reference Card  
Automatic water heater start:  
Economy mode:  
When water temperature is 1˚F (0.5˚C) lower than  
the Set Point, the heater will automatically turn on until  
water temperature reaches Set Point plus 1˚F (0.5˚C).  
Press Econo key to switch from Normal mode  
to Economy mode. In Economy mode, system  
maintains temperature at the desired Set Point  
during filter cycles only. Set Point is 20˚F (11˚C)  
below the Normal mode Set Point for the rest  
of the time. In Economy mode, the display will  
toggle between the current water temperature  
and the "Econ" message.  
The "Heater" indicator lights up when the heater is  
on. It flashes when there is a request for more  
heat but the heater has not yet started.  
N.B.: If your system is configured in Low Current Mode,  
the heater will not start if a pump is on at high speed.  
PROGRAMMING FILTER CYCLE DURATION  
The system automatically performs two filter cycles per day, at 12-hour intervals. During a filter cycle: Pump 2 and blower run  
for one minute, then Pump 1 runs at low speed for the programmed number of hours  
The "Filter Cycle" indicator lights up when the filter cycle is on. To set filter cycle duration:  
When the desired setting  
is displayed, press Filter key  
again to confirm. A filter cycle  
starts immediately.  
Press and hold Filter key  
until the display shows "xx",  
representing the currently  
set filter cycle duration in  
hours.  
Use Up or Down arrow keys  
to change setting.  
0 = no filtration  
12 = continuous filtration  
The filter cycle is suspended if the water temperature  
raises more than 2˚F (1˚C) above Set Point or if spa  
is in use (pumps, blower started manually). The "Filter"  
indicator will blink (on 0.5 second, off 0.5 second,  
on 0.5 second, off 1.5 seconds).  
N.B.: After a power failure, the filter cycle duration will  
return to its default value (2 hours). In this case, the first  
filter cycle will start one minute after power has been  
restored.  
TROUBLESHOOTING  
Pumps have started up for one  
minute on several occasions and  
"Filter Cycle" indicator is flashing.  
Not a bug but a feature!  
Our Smart Winter Mode protects your spa from the  
cold by automatically turning pumps on for one minute  
several times a day to prevent water from freezing in pipes.  
3 flashing dots are displayed.  
A problem has been detected.  
Do not enter the water! Check and open water valves.  
Clean filter if necessary. Check water level. Add water  
if needed.  
Shut power off and power your spa up again to reset  
the system.  
Call your dealer or service supplier if problem persists.  
Water temperature is flashing.  
Water temperature in the spa has reached 112˚F (44˚C).  
Do not enter the water! Allow water to cool down.  
The system will reset automatically when water temperature  
reaches 109˚F (43˚C).  
Call your dealer or service supplier if problem persists.  
The display is flashing.  
A power failure has occurred.  
Press any key to reset the system, then reprogram all  
desired parameters.  
E
Smart  
Winter  
TM  
Mode  
 
9919-100495-B  

Cooper Lighting Landscape Lighting Classical CLB 1 User Manual
DigiTech Cell Phone CO408 User Manual
Dimplex Fan DF3003 User Manual
Dynex TV DVD Combo DX LTDVD22 09 User Manual
Edimax Technology Network Router Wireless LAN Access Point User Manual
Electra Accessories Mobility Aid 88905 User Manual
Fluke Yard Vacuum 5200A User Manual
Fostex Computer Drive MR 8HD CD User Manual
Garland Convection Oven SUME 100D1 User Manual
GE Monogram Oven ZSC2200 User Manual